2026-11-17
A buyer sends an RFQ for "304 stainless steel sheet, 1.5 mm" and gets three quotations at three different prices. The reason is almost never the steel mill — it is the finish. 2B, BA, No.4 and HL are all legal, all 304, and all look grey in a photo, yet they differ in roughness, forming behaviour, reject rate and price by a margin that regularly reaches 10–20%.
This guide explains what each finish actually is, what it is worth costing, and how to write it on the purchase order so the mill cannot interpret it loosely.
| Finish | How it is produced | Typical Ra | Best for | Common mistake |
|---|---|---|---|---|
| 2B | Cold rolled, annealed and pickled, then skin-passed on polished rolls | 0.1–0.5 µm | General fabrication, welding, deep drawing, food equipment | Assuming it is "bright" — it is matte-smooth, not reflective |
| BA | Cold rolled and bright annealed in a controlled hydrogen/nitrogen atmosphere, no pickling | 0.05–0.1 µm | Cookware, sinks, mirror polishing base, parts that stay visible | Buying BA when the part will be painted or hidden — pure cost |
| No.4 | Polished with 120–150 grit abrasive belts, non-directional to semi-directional | 0.4–1.0 µm | Kitchen equipment, architectural panels, appliance fronts | Not specifying grain direction, so adjacent panels reflect differently |
| HL (hairline) | Fine, continuous abrasive grain, usually 240–320 grit, strictly directional | 0.2–0.4 µm | Elevator interiors, lifts, column covers, appliance trims | Ordering HL without a brushing direction code (vertical vs horizontal) |
2B is the finish most mills hold in stock in grades 304, 304L, 316L, 321, 430 and 201, in thickness from 0.3 mm to 3.0 mm on the cold rolled route. Because it is annealed and pickled, the surface is metallurgically clean and the internal stresses are removed, which makes it the safest choice for anything that will be welded or formed. If your part is going to be mechanically polished, sandblasted or powder coated downstream, 2B is the correct input: paying for BA and then abrading it away is wasted money.
2B is available across our cold rolled stainless steel sheet range, from 0.3 mm up to 3.0 mm, in widths up to 1500 mm.
Bright annealing removes the oxide layer in a controlled atmosphere rather than by acid, so the surface stays smoother and no pickling marks remain. Two practical consequences follow. First, the sheet polishes to a mirror far faster, which is why most 8K mirror sheet starts life as BA. Second, the lower roughness reduces friction in deep drawing, so draw ratios that fail on 2B sometimes succeed on BA.
BA costs more because the annealing line is slower and the atmosphere is expensive. Specify it when the surface will be seen, or when the forming operation is marginal. Do not specify it for structural brackets.
These two are often quoted interchangeably and should not be. No.4 uses a coarser abrasive and produces a visible, slightly randomised scratch pattern; HL uses a finer, strictly linear grain that reads as a soft sheen. On a single panel nobody notices. On a lift car with six panels meeting at 90 degrees, mismatched grain direction is immediately obvious to the client, and re-making the panels costs more than the original order.
For decorative and architectural work, the finish specification needs three parts, not one: the finish name, the grain direction relative to the panel edge, and the batch. Where a project mixes visible and non-visible panels, we normally recommend ordering the visible ones as a single production batch — colour and gloss drift between batches is real in decorative stainless steel sheet.
The cost chain runs 2B, then BA, then HL, then No.4, then 8K mirror. Stock 2B in standard sizes ships in days because it comes from routine mill production. BA and HL are usually produced to order and may add two to four weeks. Coil-fed polishing for long runs is cheaper per square metre than sheet polishing, so projects with repetitive panel sizes are often better served by ordering cold rolled stainless steel coil and having it cut and polished in one pass.
Is BA better than 2B for welding? No. BA gives a cleaner surface but the weld zone still needs pickling or passivation. Choose BA for appearance or forming, not for weldability.
Can No.4 be repaired on site? Only with the same grit and direction. Field repair of No.4 is visible under grazing light; HL is generally not repairable on site at all.
Does a smoother finish resist corrosion better? Yes, marginally. A rougher surface traps moisture and chloride, so in coastal or washdown environments a smoother finish — or a post-weld passivation step — genuinely extends service life.
If you are unsure which finish your drawing implies, send the drawing and the end use and we will tell you what the mill will actually book it as — that conversation usually saves more than the finish itself costs.
Contact Us at Any Time