Home
>
PRODUCTS
>
Stainless Steel Seamless Pipe
>
A seamless pipe above about 219 mm outside diameter is no longer a commodity item. It is produced either by hot extrusion of a pierced billet or by cross roll piercing followed by cold drawing, and the size range available at any moment depends on which mandrel and die sets the mill is running. That is why a buyer who needs 325 mm or 426 mm 201 pipe in a specific wall cannot simply order it from a catalogue: the realistic question is what the mill can roll in the next campaign.
Our range covers 21 mm to 630 mm outside diameter, wall from 2 mm to 40 mm, in lengths up to 12 m. Standard production runs 6 m; longer lengths are made to order and are limited by transport rather than by the mill.
201 is an austenitic stainless with 16 to 18 percent chromium, 3.5 to 5.5 percent nickel and 5.5 to 7.5 percent manganese. The manganese partly substitutes for nickel, which is what makes it 20 to 30 percent cheaper than 304 in a large diameter section where the weight per metre is high. For a structural column cover, a decorative sleeve, a framework or an indoor conveyor roller, it performs well and the saving is real.
It stops being a good idea in three situations. First, in chloride bearing air or water: 201 has a lower pitting resistance than 304 and will stain in coastal or marine atmospheres. Second, in welded assemblies that see humid service: the wider heat tint zone on 201 is more prone to preferential attack. Third, where the part will be deep drawn or heavily formed, because 201 work hardens faster than 304 and needs more annealing steps.
For chemical, petroleum and process piping the correct grades remain 304L and 316L, and we quote those in the same diameter range.
Large diameter seamless pipe is hot extruded, then either supplied in the hot finished condition (scaled, with a normalised structure) or cold drawn and solution annealed for a tighter tolerance and a cleaner surface. Cold drawn large diameter pipe is the more expensive route and is chosen when the pipe will be machined, threaded or used in a visible application.
| Parameter | Range |
|---|---|
| Outside diameter | 21 - 630 mm |
| Wall thickness | 2 - 40 mm |
| Length | 5.8 / 6 m standard, up to 12 m on order |
| Grades | 201, 304, 304L, 316L, 321, 310S |
| Process | Hot extruded, cold drawn, annealed and pickled |
| Surface | Pickled, bright annealed, polished on request |
| Standard | ASTM A312 / A999, EN 10216-5, GB/T 14976 |
| Test | Hydrostatic or eddy current, EN 10204 3.1 |
Wall thickness on a large diameter pipe is measured at four points around the circumference and must be within the tolerance class agreed on the order, normally plus or minus 12.5 percent for seamless. Each length is hydrostatically tested at the pressure specified in the standard, or eddy current tested where a non destructive method is preferred. Dimensional reports, PMI by XRF and ultrasonic wall measurement can be added when the pipe is going into a pressure application.
For 201 in structural use, buyers often ask only for the mill certificate. That is reasonable, but the certificate should show the actual chemistry of the heat rather than a generic grade statement, because manganese and nickel content vary more widely in 201 than in 304 and the variation affects both corrosion behaviour and weldability.
Large diameter pipe is normally cut to length at our works with a band saw or plasma, and bevelled for welding where requested. A 630 mm pipe in 20 mm wall weighs about 300 kg per metre, so a 6 m length is 1.8 tonnes: shipping is planned around the crane capacity at both ends, and the buyer should confirm the unloading equipment at destination before the length is fixed.
What is the minimum order for a non standard diameter?
One tonne, or one length where the piece weight is above one tonne.
Can you supply 201 and 304 in the same shipment?
Yes, and we mark each length with the grade so the two are not mixed on site.
Is the pipe suitable for bending?
Cold drawn and annealed pipe bends well up to about 3D radius. Hot finished pipe should be annealed after bending.
Do you supply cut rings or flanges?
Yes, cut rings, saddles and bevelled ends can be produced to a drawing.
Contact Us at Any Time