Home
>
PRODUCTS
>
Stainless Steel Sheets Metal
>
The trade uses the words loosely, but the standards do not. A sheet is thin enough to be coiled and is normally cold rolled; a plate is thicker and is normally hot rolled and sold flat. The dividing line is around 3 mm in the EN system and around 4.75 mm in the American one, which is why a 4 mm product can be quoted either way depending on which standard the buyer is working to.
It matters for three reasons: the tolerance, the flatness and the price basis. Cold rolled sheet is held to a tight gauge and has a good surface; hot rolled plate carries a mill scale that has to be removed and a thickness tolerance roughly three times wider. If the drawing says 3 mm and the inspector measures 3.4 mm, whether that passes depends entirely on which product was ordered.
Everything on this page is cold rolled sheet, 0.3 to 3 mm, supplied with a slit edge and cut to length or supplied as coil.
Standard cold rolled sheet thickness tolerance depends on width and thickness, and for a 1 mm sheet at 1219 mm wide it is around plus or minus 0.05 mm. Precision rolling can hold plus or minus 0.02 mm, at a price.
The question is whether the process needs it. A press forming a shallow pan will run happily on standard tolerance. A progressive die blanking a part that stacks, or a roll forming line setting a fixed gap, needs the tighter band because the variation accumulates over a run. Buy the tolerance the process needs, not the tightest one available, because the price difference is real and the benefit is often invisible.
The same logic applies to flatness. A sheet that is flat to 3 mm over a metre is normal; a sheet for a laser cutting bed or a visible panel wants 1 mm, and that is achieved by tension levelling, not by rolling harder.
These two grades are at opposite ends of the stainless family and they are bought for opposite reasons, so a supplier listed against both is normal.
310S is 25 percent chromium and 20 percent nickel, an austenitic for high temperature service. It resists oxidation to about 1100 C and is used for furnace liners, burner parts, kiln internals and heat shields. It is the most expensive grade on this page by a wide margin and it is not a corrosion grade: in wet chloride it is worse than 316, because it has no molybdenum.
410 is 12 percent chromium martensitic, magnetic, hardenable, and cheap. It is used for wear parts, cutlery, turbine blades and applications where a hard surface matters more than corrosion resistance. It welds with difficulty and it will rust in a wet environment.
The commercial consequence: a fabricator who orders 310S and receives 410 will usually notice, because 410 is magnetic and 310S is not. A magnet is the fastest field check in the warehouse, and it is worth carrying one.
| Parameter | Value |
|---|---|
| Grade | 201, 304, 304L, 316L, 310S, 410, 430 |
| Thickness | 0.3 to 3.0 mm |
| Thickness tolerance | Standard per ASTM A480, or plus or minus 0.02 mm precision |
| Width | Slit 20 to 1500 mm, mill edge 1000 / 1219 / 1500 mm |
| Length | Cut to order, 500 to 6000 mm |
| Edge | Slit edge, deburred on request |
| Finish | 2B, BA, No.4, HL, 8K, PVC coated |
| Flatness | 3 mm per metre standard, 1 mm after tension levelling |
| Standard | ASTM A240, A480, EN 10088-2 |
| Test | EN 10204 3.1, PMI, dimensional report |
A good slit edge is straight, square to the face, free of a turned over lip, and carries a burr no taller than about 5 percent of the thickness. A poor one shows a wave along the edge, a burr that can cut a glove, or a rainbow discolouration from a dull knife rubbing rather than cutting.
Ask for the burr to be on a specified face if the sheet will be stacked or fed through a machine. Ask for the edge to be deburred if it will be handled, coated, or visible. And ask for the coil to be edge trimmed after slitting if the material is going into a welded tube mill, because a burr on the strip edge becomes a weld defect that shows up as a line of porosity.
Coils are shipped eye to sky, standing on end, or eye to wall, lying on the side. Eye to sky is the normal sea freight orientation and uses the coil weight to keep it stable, but it exposes the wrap to water pooling if the container roof leaks. Eye to wall is easier to handle with a forklift and is preferred by many fabricators, but it needs a cradle and takes more floor space.
Cut sheets go on a wooden pallet with a cardboard or plastic interleaf, strapped, and ideally with edge protection. A pallet of 1 mm sheet that has been strapped without edge protection will show a dent line 200 mm in from each edge, and that band is scrap.
Can you supply 310S in 1 mm?
Yes, cold rolled to order. Lead time is longer than 304 because it is not a stock gauge.
Is the gauge measured before or after polishing?
Before. Polishing removes 0.02 to 0.05 mm depending on the finish, so a polished 1 mm sheet measures slightly under.
Can you mix grades on one pallet?
Yes, but each bundle must be tagged separately and the packing list must show the grade per bundle.
Do you supply a mill certificate with the heat number?
Yes, EN 10204 3.1 as standard, with the heat number matching the bundle tag.
Contact Us at Any Time