logo
Foshan Sewaly Steel Co.,Ltd
ईमेल alla@sewaly.com टेलीफोन 86-186-7659-9928
घर
घर
>
समाचार
>
कंपनी समाचार के बारे में Stainless Steel Circles for Cookware: Grade, Thickness, Yield
घटनाएँ
एक संदेश छोड़ें

Stainless Steel Circles for Cookware: Grade, Thickness, Yield

2026-11-17

नवीनतम कंपनी समाचार के बारे में Stainless Steel Circles for Cookware: Grade, Thickness, Yield

Cookware factories rarely buy sheet. They buy circles, because a circle blank is the only shape that gives a predictable yield from a rectangular sheet — and because the circle producer absorbs the scrap. The purchasing decision therefore has three variables that sheet buyers never think about: diameter tolerance, earring behaviour after drawing, and how the blank nests on the master coil width.

Here is how to specify circles so the press shop does not end up rejecting a container of blanks.

Start with the pan, not the grade

The grade is decided by the cooking surface and the heat source, not by what is cheapest per tonne.

Cookware type Typical grade Thickness Why
Stainless frying pan, sandwich base, gas/halogen 304 (food contact layer) + 430 or aluminium core 0.5–0.8 mm inner, 0.5 mm outer 430 is ferritic and magnetic, so it couples with induction; 304 gives the hygienic cooking face
Induction-ready pan, single layer 430 / 441 0.6–1.0 mm Ferritic grades respond to induction without an added base plate
Stock pot, heavy gauge 304 0.8–1.2 mm Wall stiffness and resistance to denting under load
Pressure cooker body 304 / 304L 1.0–1.5 mm Hoop strength and weldability at the base seam
Economy cookware, non-critical 201 0.5–0.7 mm Lower nickel content, lower cost, adequate for dry use

A common cost mistake is ordering 304 for the entire sandwich base. Only the food-contact layer needs to be 304; the outer induction layer is normally 430, and the core is aluminium for heat spreading. Splitting the specification by layer typically cuts material cost substantially without touching the cooking performance.

Deep drawing quality is the spec people forget

A circle that measures correctly can still fail in the press. Deep drawing demands a specific metallurgical state: annealed, with a grain size controlled to roughly ASTM E112 grain 6–8, and with low earing so the drawn cup has an even rim height. Two consequences for the purchase order:

  • Ask for "deep drawing quality, annealed, grain size 6–8" in writing — not simply "304".
  • Ask for the earing percentage if the draw ratio is aggressive. A 3% earing difference shows up as a wavy rim that needs extra trimming, and trimming is labour.

Likewise, 2B and BA behave differently in the press. BA's lower roughness reduces friction, so marginal draw ratios that tear on 2B sometimes run cleanly on BA. If the part is deep and the surface is visible, BA is usually the right input even at higher cost. If you would rather blank in-house than buy pre-cut circles, both finishes are available on cold rolled stainless steel sheet in 0.3–3.0 mm.

The tolerances that actually cause scrap

In our experience the rejection causes rank in this order:

  1. Diameter tolerance. Too loose and the blank does not centre in the die; too tight and the nesting cost rises. State the tolerance explicitly, e.g. ±0.2 mm for blanks under 400 mm.
  2. Burr height. Burr on the blank becomes a crack initiation point during drawing. Specify a maximum burr, and state which side the burr is allowed on.
  3. Flatness and camber. A circle that is dished by more than a fraction of a millimetre will not sit flat in the die, and the drawn part inherits the error.
  4. Edge condition. Sheared versus laser-cut edges behave differently; laser edges are cleaner but can leave a hardened zone that matters for very small radii.

We cut stainless steel discs from cold rolled coil on CNC circle-cutting lines, which keeps diameter tolerance and burr consistent across a run; that consistency is worth more to a press shop than a marginally lower unit price.

Yield: why the coil width decides your price

A 500 mm circle nested on a 1000 mm coil width gives two rows and effectively zero waste. The same circle on a 1219 mm coil leaves 219 mm of scrap per row unless that strip is sold on. This is why a quotation for circles can differ by more than 10% between suppliers using different master coil widths — the difference is not the steel, it is the nesting.

If your annual volume is meaningful, tell the supplier your monthly diameter mix rather than a single size. A supplier who can group your diameters onto one coil width will price the whole programme lower than someone quoting each size independently. Leftover strip from circle cutting is also why narrow stainless steel strips are often available at better prices than fresh slit coil.

Packing, because circles damage easily

Circles are thin, round and stack badly. Edge knocks during transit become dents that show after polishing. Specify: interleaved paper or film between blanks, edge protection on the bundle, and a maximum stack height. For visible cookware, PVC film on the polished face is standard, but confirm the film grade — a cheap film left on for weeks in a hot container leaves adhesive residue that has to be removed before assembly.

Ordering checklist

  • Diameter and tolerance, in mm, with the measuring method
  • Thickness and tolerance class
  • Grade per layer, if a sandwich base
  • Finish: 2B or BA, and whether one face must be protected
  • Deep drawing quality, grain size, earing limit
  • Burr limit and permitted side
  • Packing method and stack height
  • Test certificate 3.1 and PMI on arrival

Send the pan drawing and the press tonnage, and the circle specification usually writes itself — the two numbers that matter are the draw ratio and the induction requirement, and everything else follows from them.

किसी भी समय हमसे संपर्क करें

86-186-7659-9928
नंबर 13, फोचेन रोड, चेनकुन टाउन, शुंडे जिला, फोशन शहर, गुआंग्डोंग प्रांत, चीन
अपनी पूछताछ सीधे हमें भेजें