2026-11-17
Cookware factories rarely buy sheet. They buy circles, because a circle blank is the only shape that gives a predictable yield from a rectangular sheet — and because the circle producer absorbs the scrap. The purchasing decision therefore has three variables that sheet buyers never think about: diameter tolerance, earring behaviour after drawing, and how the blank nests on the master coil width.
Here is how to specify circles so the press shop does not end up rejecting a container of blanks.
The grade is decided by the cooking surface and the heat source, not by what is cheapest per tonne.
| Cookware type | Typical grade | Thickness | Why |
|---|---|---|---|
| Stainless frying pan, sandwich base, gas/halogen | 304 (food contact layer) + 430 or aluminium core | 0.5–0.8 mm inner, 0.5 mm outer | 430 is ferritic and magnetic, so it couples with induction; 304 gives the hygienic cooking face |
| Induction-ready pan, single layer | 430 / 441 | 0.6–1.0 mm | Ferritic grades respond to induction without an added base plate |
| Stock pot, heavy gauge | 304 | 0.8–1.2 mm | Wall stiffness and resistance to denting under load |
| Pressure cooker body | 304 / 304L | 1.0–1.5 mm | Hoop strength and weldability at the base seam |
| Economy cookware, non-critical | 201 | 0.5–0.7 mm | Lower nickel content, lower cost, adequate for dry use |
A common cost mistake is ordering 304 for the entire sandwich base. Only the food-contact layer needs to be 304; the outer induction layer is normally 430, and the core is aluminium for heat spreading. Splitting the specification by layer typically cuts material cost substantially without touching the cooking performance.
A circle that measures correctly can still fail in the press. Deep drawing demands a specific metallurgical state: annealed, with a grain size controlled to roughly ASTM E112 grain 6–8, and with low earing so the drawn cup has an even rim height. Two consequences for the purchase order:
Likewise, 2B and BA behave differently in the press. BA's lower roughness reduces friction, so marginal draw ratios that tear on 2B sometimes run cleanly on BA. If the part is deep and the surface is visible, BA is usually the right input even at higher cost. If you would rather blank in-house than buy pre-cut circles, both finishes are available on cold rolled stainless steel sheet in 0.3–3.0 mm.
In our experience the rejection causes rank in this order:
We cut stainless steel discs from cold rolled coil on CNC circle-cutting lines, which keeps diameter tolerance and burr consistent across a run; that consistency is worth more to a press shop than a marginally lower unit price.
A 500 mm circle nested on a 1000 mm coil width gives two rows and effectively zero waste. The same circle on a 1219 mm coil leaves 219 mm of scrap per row unless that strip is sold on. This is why a quotation for circles can differ by more than 10% between suppliers using different master coil widths — the difference is not the steel, it is the nesting.
If your annual volume is meaningful, tell the supplier your monthly diameter mix rather than a single size. A supplier who can group your diameters onto one coil width will price the whole programme lower than someone quoting each size independently. Leftover strip from circle cutting is also why narrow stainless steel strips are often available at better prices than fresh slit coil.
Circles are thin, round and stack badly. Edge knocks during transit become dents that show after polishing. Specify: interleaved paper or film between blanks, edge protection on the bundle, and a maximum stack height. For visible cookware, PVC film on the polished face is standard, but confirm the film grade — a cheap film left on for weeks in a hot container leaves adhesive residue that has to be removed before assembly.
Send the pan drawing and the press tonnage, and the circle specification usually writes itself — the two numbers that matter are the draw ratio and the induction requirement, and everything else follows from them.