Home
>
PRODUCTS
>
Stainless Steel Pipe Fittings
>
A sanitary fitting is not a polished industrial fitting. It has to do three things at once: leave no crevice where product can sit, present a surface a cleaning cycle can reach and flush, and connect to tubing on a fixed dimensional standard so parts from different suppliers still mate. That is why the ends here are tri clamp ferrules, IDF unions or butt weld ends to DIN 11850 and ISO 2037 rather than threaded NPT. Threads are where a wash cycle fails first.
We make them in 304 and 316L, DN10 to DN150, with finishes from Ra 1.6 um to Ra 0.4 um on request.
| Material | 304, 316L (316Ti, 321, 2205 on request) |
|---|---|
| Size range | DN10 - DN150 (1/2 inch - 6 inch) |
| Wall thickness | 1.5 mm, 1.6 mm, 2.0 mm, or matched to the tube schedule |
| Connection | Tri clamp (TC), IDF/ISS, butt weld, NPT, BSP |
| Surface finish | Ra 1.6 um standard; Ra 0.8 um and Ra 0.4 um on request; electropolished optional |
| Dimensional standard | DIN 11850, ISO 2037, 3-A Sanitary Standards |
| Material standard | ASTM A270, EN 10088 |
| Pressure rating | 10 bar at ambient for clamp joints, higher for butt weld |
| Certificate | EN 10204 3.1 mill test certificate per heat, traceable to the melt number |
| Minimum order | 1 ton, mixed sizes allowed |
| Lead time | 7 to 25 days depending on size and finish |
Most leaks and contamination events in a hygienic line start at the joint, not at the tube wall. A tri clamp joint seals on a gasket compressed between two flat ferrule faces, so both faces need to be square and the gasket needs the right durometer for the temperature. A butt weld joint removes the gasket entirely, but it only works if the bore is matched and the weld is purged and polished afterwards. Where a line will be cleaned in place and never opened, weld it. Where it will be opened for inspection, clamp it.
304 covers clean water, milk, beer and most neutral food products. 316L adds 2 to 3 percent molybdenum, which is what resists chlorides, brines and the chloride based cleaning chemicals used in cheese and seafood plants. 316L also caps carbon at 0.03 percent, which keeps chromium carbides from forming in the weld heat affected zone. If the assembly is welded and then put into service without solution annealing, specify 316L.
Ra is arithmetic mean roughness, and the number that matters depends on who is auditing. 3-A Sanitary Standards call for a product contact surface no rougher than Ra 0.8 um (32 microinch). For most dairy and beverage work that is enough. Electropolishing is what gets below it, because it removes the deformed layer left by mechanical polishing and leaves a chromium rich passive skin. For aseptic duty or long residence time product, go lower.
Dairy reception lines and cheese vats, brewery transfer and fermentation, beverage blending, bakery and confectionery syrup lines, edible oil, personal care and cosmetics, and clean utility loops for water and air. In every case the fitting is matched to the tube outside diameter, wall thickness and end preparation, so the bore stays continuous through the joint.
Each lot ships with a mill test certificate showing chemical composition and mechanical properties, traceable to the heat number. Dimensions are checked against DIN 11850, covering outside diameter, wall thickness and face squareness. Surface finish is measured on a sample basis and reported as Ra. Third party inspection by BV or TUV can be arranged before shipment.
Five details get an accurate quote: fitting type, size in DN or inches, end connection, material grade and surface finish. Mixed containers are routine, so elbows, tees and ferrules can ship together. Standard export packing is a carton inside a wooden case, with each piece sleeved to protect the polished surface.
Can you supply 3-A marked fittings? Yes, the range is produced to 3-A Sanitary Standards dimensions and finish on request.
Do you supply both tri clamp and butt weld ends? Yes, in the same size range and grade, so a line can mix both joint types.
What gasket material do you recommend? EPDM for most food and dairy duty, silicone for higher temperature, PTFE encapsulated for aggressive chemicals.
What is the minimum order? One ton, with mixed sizes and types allowed in the same grade.
Contact Us at Any Time