Home
>
PRODUCTS
>
Stainless Steel Disc
>
Both start as cold rolled sheet, and both are annealed. The difference is the atmosphere in the furnace.
2B is annealed in a normal atmosphere, which leaves an oxide scale on the surface, and the scale is then removed by pickling and the sheet is skin passed between polished rolls. The result is a matte, slightly grey surface with a low roughness, uniform, and cheap to produce because the line runs fast.
BA is bright annealed in a hydrogen or nitrogen-hydrogen atmosphere, so no oxide forms in the first place and no pickling is needed. The surface stays reflective, the roughness is lower, and the sheet looks like a mirror that has not been polished. It costs more because the furnace is slower, the atmosphere is expensive, and the coil must be clean before it goes in.
For a part that will be drawn or formed, 2B is normally enough. For a visible flat part, a decorative ring, a lamp reflector or a trim disc, BA is what the customer is actually asking for when they say they want it to look like stainless.
Two millimetres sits at a useful point in the sheet range. It is thick enough to hold its shape as a free disc, to take a thread or a weld, and to resist denting in handling, and it is thin enough to be cut on a circle shear, drawn into a shallow part, and packed economically.
That is why it turns up in so many unrelated applications: cooker hood covers, sink wastes and drain covers, flue caps, decorative wall discs, table bases, speaker plates, machine guards, and the bottom plates of small tanks. It is also the gauge where the difference between cold rolled sheet and hot rolled plate starts to matter, because 2 mm is at the thin end of the hot rolled range and the thick end of the cold rolled one. A 2 mm hot rolled disc will have a pickled No.1 surface; a 2 mm cold rolled disc will have 2B or BA. They are not interchangeable visually.
Circle shear is the production method for cookware and general discs. A blank is clamped on a rotating table and a blade trims it to diameter in one pass. Speed is high, cost is low, tolerance is around plus or minus 0.2 mm, and the edge is square with a burr on one face.
Laser is used when the diameter tolerance has to be tight, when the disc has holes or a profile, or when the quantity is too small to justify a shear set up. Tolerance is plus or minus 0.1 mm, the edge is clean, and the heat affected zone is a few tenths of a millimetre wide. On a 2 mm disc, that HAZ is visible as a faint blue line and it must be removed before welding or polishing.
Waterjet cuts with no heat at all, which matters for a part that must not distort or lose its BA finish at the edge. It is slower and more expensive per part, and it is the right answer for a thick disc with a mirror finish where a blue edge would be a defect.
| Parameter | Value |
|---|---|
| Grade | 201, 304, 304L, 316L, 430 |
| Thickness | 2.0 mm standard, 0.3 to 4.0 mm other gauges |
| Diameter | 100 to 1000 mm |
| Diameter tolerance | plus or minus 0.2 mm sheared, plus or minus 0.1 mm laser |
| Finish | 2B, BA, No.4, HL, or PVC coated |
| Thickness tolerance | per ASTM A480, or plus or minus 0.02 mm precision |
| Flatness | 2 mm per metre, 1 mm after levelling |
| Edge | Sheared, laser cut, deburred on request |
| Standard | ASTM A240, A480, EN 10088-2 |
| Test | MTC 3.1, PMI, dimensional report |
A disc that is dished by 3 mm will not stack flat, and a stack of 200 discs with a 3 mm dish becomes a bundle that leans, straps badly, and arrives deformed. Flatness on a cut disc comes from the parent sheet, not from the cutting, unless the cut put heat into the part. That is why a laser cut disc from a sheet with residual stress can bow after cutting: the cut releases the stress on one side.
Burr is the second. A sheared disc has a burr on the underside, and a stack of discs with the burr all facing the same way will interlock and be difficult to separate. For automated feeding, specify a deburred edge or a burr height limit, typically 0.05 mm on 2 mm material.
Both are worth a sentence on the purchase order. Neither is expensive to control at the works, and both are expensive to discover at the press.
A "multi size" order is normal in this trade: a cookware range in four diameters, a fabricator stocking three sizes, a distributor wanting a mixed pallet. The economics are driven by nesting. Discs of 200, 240 and 280 mm nest on a 1219 mm sheet far better than a single size at a round number, because the offcut between circles can be used by a smaller size.
Send the full list with quantities rather than one size at a time. A mixed order can reduce the material cost by 5 to 10 percent against the same tonnage in a single size, and the packing is easier because the small discs fill the gaps around the large ones.
Can you supply BA on both faces?
Yes, BA sheet is bright on both sides as produced. A one side polish is a separate operation.
Is 2 mm available in 316L?
Yes, cold rolled and cut to diameter, with a longer lead time than 304.
What is the smallest diameter you cut?
Around 100 mm on a shear; smaller discs are laser cut or punched.
Can the discs be supplied with a centre hole?
Yes, laser cut to a drawing, with the hole and the outside diameter in one operation.
Contact Us at Any Time