Home
>
PRODUCTS
>
Stainless Steel Disc
>
Five and a half millimetres is above the cold rolled sheet range, so this is a hot rolled and pickled plate that has been cut into a circle. That single fact changes three things: the surface is No.1 rather than 2B or BA, the thickness tolerance is wider, and the edge cannot be produced on a circle shear.
The No.1 surface is grey and matte, with a roughness around 2 to 3 micrometres, and it will show roll marks. If the disc is a visible part, it has to be polished or machined after cutting, and that has to be in the price from the start rather than discovered at the finishing stage.
The thickness tolerance on a 5.5 mm hot rolled plate is typically plus or minus 0.3 to 0.5 mm depending on width. If the disc is a flange that will be bolted against a gasket, or a spacer that sets a gap, that tolerance is the dimension that matters and it should be stated as a machined requirement rather than a rolled one.
For a food plant, 304 covers most dry and aqueous contact: conveyor parts, table tops, hopper liners, covers, chute components. It is the grade most food equipment is built from and it is accepted by the usual hygiene standards.
316L is specified when the surface sees chloride. That includes saline product, brining, seafood, dairy with chloride based sanitisers, and any plant that foams with hypochlorite. It also includes equipment washed with chlorinated water and left wet between shifts, which is the most common real cause of pitting in a food factory.
The molybdenum in 316L is what raises the pitting resistance, and it is worth remembering that it does nothing for a crevice. A disc bolted to a frame with a gap behind it will crevice corrode in 304 and often in 316L as well, because the crevice traps chlorides and excludes oxygen. The design fix is a welded, fully penetrated joint or a gap wide enough to clean, not a higher grade.
Plasma is the economical choice from about 4 mm upward. It cuts fast, it handles 5.5 mm easily, and the edge it leaves is slightly bevelled with a nitride layer and a heat affected zone of 0.5 to 1.5 mm. That layer must be ground back before welding, because welding through a nitrided edge produces porosity. For a disc that will not be welded, plasma is fine and the cheapest route.
Laser gives a squarer edge and a narrower HAZ, but on 5.5 mm stainless the cutting speed drops and the gas consumption rises, so the cost per part is higher than plasma. It is the right choice when the disc needs a hole pattern or a tight diameter tolerance in the same operation.
Waterjet cuts cold, with no HAZ and no oxide, and holds a tolerance of about plus or minus 0.2 mm on this thickness. It is the answer for a part that must not distort, or where the edge will be a sealing face and any scale would be a leak path. It is the slowest and most expensive of the three.
| Parameter | Value |
|---|---|
| Grade | 304, 304L, 316L, 321, 310S on request |
| Thickness | 5.5 mm standard, 3 to 20 mm other thicknesses |
| Thickness tolerance | plus or minus 0.3 mm rolled, 0.1 mm machined |
| Diameter | 200 to 1200 mm |
| Diameter tolerance | plus or minus 0.5 mm plasma, 0.2 mm waterjet |
| Surface | No.1 pickled, or polished and machined on request |
| Edge | Plasma, laser, waterjet, or machined |
| Flatness | 3 mm per metre, improved by machining |
| Standard | ASTM A240, A480, EN 10028-7 |
| Test | MTC 3.1 with heat number, PMI, UT on request |
A 5.5 mm plate cut into a 900 mm circle will not be flat to the standard of a machined part. Hot rolled plate carries a crown from rolling and a certain amount of residual stress, and when a large circle is cut out of it the balance changes and the disc can bow by a few millimetres.
If the disc is a flange face, a gasket seat or a mounting plate, order it with machining allowance: 3 mm on diameter and 1 mm on each face, then face it in the customer's shop or ours. Trying to hold a flatness of 0.2 mm on a plasma cut plate is a losing argument, and it is cheaper to machine than to sort.
For a disc that is a liner or a cover, none of this matters. State which one it is at the enquiry, because the price difference between a cut disc and a cut and machined disc is substantial.
A plate has a heat number stamped or stencilled on it, and once it is cut into eight discs that marking is gone. The traceability has to be transferred: each disc or bundle is tagged with the heat number, and the certificate covers the heat, not the individual piece.
For a food or pharmaceutical plant this is usually enough, but two things are worth adding. A PMI check on the finished disc confirms the grade after cutting and any welding, and a dimensional report on the first piece confirms the diameter and thickness before the batch runs. Both are cheap at the works and expensive to arrange after the equipment has been installed.
Can you supply 5.5 mm in 316L?
Yes, hot rolled plate, cut to diameter, with the heat number on each bundle tag.
Is the edge good enough to weld without machining?
For a plasma cut edge, grind back the HAZ first. For waterjet, the edge can be welded directly.
Can the disc be machined to a flatness of 0.1 mm?
Yes, with allowance for facing on both sides. State the flatness and the surface finish required.
What is the largest diameter you can cut?
1200 mm from plate on our plasma and waterjet beds. Larger sizes are quoted individually.
Contact Us at Any Time